(Gelöst) Probleme mit WLAN-Stick von AVM und Suse 10.2

Status
Für weitere Antworten geschlossen.

hansi

New Member
hallo zusammen.

ich habe ein problem meinen WLAN-Stick von AVM zum laufen zu bekommen.
"framp" spuckt folgendes aus:

Code:
collectNWData.sh: Collecting local network informations ...
################lo        no wireless extensions.

eth0      no wireless extensions.

sit0      no wireless extensions.

ippp0     no wireless extensions.

#collectNWData.sh 0.3.4
Invocation parameters:

*** uname -a
Linux linux-97gz 2.6.18.2-34-xenpae #1 SMP Mon Nov 27 11:46:27 UTC 2006 i686 athlon i386 GNU/Linux

*** cat /etc/SuSE-release
openSUSE 10.2 (i586)
VERSION = 10.2

*** cat /etc/resolv.conf | grep -v "^#" | grep -v "^$"
search site
nameserver 62.104.191.241
nameserver 62.104.196.134

*** cat /etc/hosts | grep -v "^#" | grep -v "^$" | grep -v "::"
127.0.0.1       localhost
192.168.178.20  linux-97gz.site linux-97gz

*** cat /proc/sys/net/ipv4/ip_forward
0

*** iptables -t nat -L
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination

Chain POSTROUTING (policy ACCEPT)
target     prot opt source               destination

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination

*** route -n
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
62.104.207.34   0.0.0.0         255.255.255.255 UH    0      0        0 ippp0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         62.104.207.34   0.0.0.0         UG    0      0        0 ippp0

*** ifconfig
eth0      Protokoll:Ethernet  Hardware Adresse 00:0B:6A:66:2A:4F
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:20 Basisadresse:0xd400

ippp0     Protokoll:Punkt-zu-Punkt Verbindung
          inet Adresse:89.50.188.245  P-z-P:62.104.207.34  Maske:255.255.255.255
          UP PUNKTZUPUNKT RUNNING NOARP DYNAMIC  MTU:1500  Metric:1
          RX packets:6299 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5532 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:30
          RX bytes:6388578 (6.0 Mb)  TX bytes:646315 (631.1 Kb)

lo        Protokoll:Lokale Schleife
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:336 errors:0 dropped:0 overruns:0 frame:0
          TX packets:336 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0
          RX bytes:25232 (24.6 Kb)  TX bytes:25232 (24.6 Kb)


*** pingMyLocalIPs
89.50.188.245 : Ping response
127.0.0.1 : Ping response

*** ping -c1 -W 3 195.135.220.3
PING 195.135.220.3 (195.135.220.3) 56(84) bytes of data.
64 bytes from 195.135.220.3: icmp_seq=1 ttl=57 time=54.2 ms

--- 195.135.220.3 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 54.220/54.220/54.220/0.000 ms

*** ping -c1 -W 3 www.suse.de
PING turing.suse.de (195.135.220.3) 56(84) bytes of data.
64 bytes from turing.suse.de (195.135.220.3): icmp_seq=1 ttl=57 time=67.9 ms

--- turing.suse.de ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 67.950/67.950/67.950/0.000 ms

*** lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:09.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:0a.0 FireWire (IEEE 1394): NEC Corporation uPD72874 IEEE1394 OHCI 1.1 3-port PHY-Link Ctrlr (rev 01)
00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)
00:0c.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)

*** lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 004 Device 004: ID 057c:5601 AVM GmbH
Bus 004 Device 002: ID 04a9:10a5 Canon, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
 

hansi

New Member
AW: Probleme mit WLAN-Stick von AVM und Suse 10.2

Teil 2...

Code:
*** iptables -L -vn
Chain INPUT (policy DROP 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
   34  2292 ACCEPT     0    --  lo     *       0.0.0.0/0            0.0.0.0/0   
 6157 6350K ACCEPT     0    --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED
  132 13048 input_ext  0    --  ippp0  *       0.0.0.0/0            0.0.0.0/0   
    0     0 input_ext  0    --  *      *       0.0.0.0/0            0.0.0.0/0   
    0     0 LOG        0    --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 LOG flags 6 level 4 prefix `SFW2-IN-ILL-TARGET '
    0     0 DROP       0    --  *      *       0.0.0.0/0            0.0.0.0/0   

Chain FORWARD (policy DROP 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 LOG        0    --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 LOG flags 6 level 4 prefix `SFW2-FWD-ILL-ROUTING '

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
   34  2292 ACCEPT     0    --  *      lo      0.0.0.0/0            0.0.0.0/0   
 5524  624K ACCEPT     0    --  *      *       0.0.0.0/0            0.0.0.0/0           state NEW,RELATED,ESTABLISHED
    0     0 LOG        0    --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 LOG flags 6 level 4 prefix `SFW2-OUT-ERROR '

Chain forward_ext (0 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain input_ext (2 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 DROP       0    --  *      *       0.0.0.0/0            0.0.0.0/0           PKTTYPE = broadcast
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           icmp type 4
    5   305 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           icmp type 8
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 0
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 3
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 11
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 12
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 14
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 18
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 3 code 2
    0     0 ACCEPT     icmp --  *      *       0.0.0.0/0            0.0.0.0/0           state RELATED,ESTABLISHED icmp type 5
    0     0 reject_func  tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           tcp dpt:113 state NEW
    0     0 LOG        0    --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 PKTTYPE = multicast LOG flags 6 level 4 prefix `SFW2-INext-DROP-DEFLT '
    0     0 DROP       0    --  *      *       0.0.0.0/0            0.0.0.0/0           PKTTYPE = multicast
   79  3880 LOG        tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 tcp flags:0x17/0x02 LOG flags 6 level 4 prefix `SFW2-INext-DROP-DEFLT '
    0     0 LOG        icmp --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 LOG flags 6 level 4 prefix `SFW2-INext-DROP-DEFLT '
   15  7211 LOG        udp  --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 LOG flags 6 level 4 prefix `SFW2-INext-DROP-DEFLT '
    2   120 LOG        0    --  *      *       0.0.0.0/0            0.0.0.0/0           limit: avg 3/min burst 5 state INVALID LOG flags 6 level 4 prefix `SFW2-INext-DROP-DEFLT-INV '
  127 12743 DROP       0    --  *      *       0.0.0.0/0            0.0.0.0/0   

Chain reject_func (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 REJECT     tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           reject-with tcp-reset
    0     0 REJECT     udp  --  *      *       0.0.0.0/0            0.0.0.0/0           reject-with icmp-port-unreachable
    0     0 REJECT     0    --  *      *       0.0.0.0/0            0.0.0.0/0           reject-with icmp-proto-unreachable

*** cat /etc/sysconfig/SuSEfirewall2 | grep -v "^#" | grep -v "^$"
FW_DEV_EXT="any ippp0 wlan-bus-usb-1-5:1.0"
FW_DEV_INT=""
FW_DEV_DMZ=""
FW_ROUTE="no"
FW_MASQUERADE="no"
FW_MASQ_DEV="$FW_DEV_EXT"
FW_MASQ_NETS="0/0"
FW_PROTECT_FROM_INT="no"
FW_SERVICES_EXT_TCP=""
FW_SERVICES_EXT_UDP=""
FW_SERVICES_EXT_IP=""
FW_SERVICES_EXT_RPC=""
FW_CONFIGURATIONS_EXT=""
FW_SERVICES_DMZ_TCP=""
FW_SERVICES_DMZ_UDP=""
FW_SERVICES_DMZ_IP=""
FW_SERVICES_DMZ_RPC=""
FW_CONFIGURATIONS_DMZ=""
FW_SERVICES_INT_TCP=""
FW_SERVICES_INT_UDP=""
FW_SERVICES_INT_IP=""
FW_SERVICES_INT_RPC=""
FW_CONFIGURATIONS_INT=""
FW_SERVICES_DROP_EXT=""
FW_SERVICES_REJECT_EXT="0/0,tcp,113"
FW_SERVICES_ACCEPT_EXT=""
FW_TRUSTED_NETS=""
FW_ALLOW_INCOMING_HIGHPORTS_TCP=""
FW_ALLOW_INCOMING_HIGHPORTS_UDP=""
FW_FORWARD=""
FW_FORWARD_MASQ=""
FW_REDIRECT=""
FW_LOG_DROP_CRIT="yes"
FW_LOG_DROP_ALL="no"
FW_LOG_ACCEPT_CRIT="yes"
FW_LOG_ACCEPT_ALL="no"
FW_LOG_LIMIT=""
FW_LOG=""
FW_KERNEL_SECURITY="yes"
FW_STOP_KEEP_ROUTING_STATE="no"
FW_ALLOW_PING_FW="yes"
FW_ALLOW_PING_DMZ="no"
FW_ALLOW_PING_EXT="no"
FW_ALLOW_FW_SOURCEQUENCH=""
FW_ALLOW_FW_BROADCAST_EXT="no"
FW_ALLOW_FW_BROADCAST_INT="no"
FW_ALLOW_FW_BROADCAST_DMZ="no"
FW_IGNORE_FW_BROADCAST_EXT="yes"
FW_IGNORE_FW_BROADCAST_INT="no"
FW_IGNORE_FW_BROADCAST_DMZ="no"
FW_ALLOW_CLASS_ROUTING=""
FW_CUSTOMRULES=""
FW_REJECT=""
FW_REJECT_INT="yes"
FW_HTB_TUNE_DEV=""
FW_IPv6=""
FW_IPv6_REJECT_OUTGOING=""
FW_IPSEC_TRUST="no"
FW_ZONES=""
FW_USE_IPTABLES_BATCH=""
FW_LOAD_MODULES=""
FW_FORWARD_ALWAYS_INOUT_DEV=""
FW_SERVICES_ACCEPT_INT=""
FW_SERVICES_ACCEPT_DMZ=""

*** iwconfig | sed "s/\(Encryption key:\)\([^o][^f][^f][^ ]*\)\(.*\)/\1xx xxx-xxxx-xxxx-xxxx-xxxx-xxxxxxx\3/"

*** catMyConfig
*** cat /etc/sysconfig/network/ifcfg-ippp0
STARTMODE="manual"
IPADDR="192.168.99.1"
PTPADDR="192.168.99.2"
DEFAULTROUTE="yes"
FIREWALL="yes"
MSN="401276"
DIALMODE="manual"
PROVIDER="mobilcom1"
SECURE="on"
CHARGEHUP="on"
CALLBACK="off"
CBDELAY="2"
MULTILINK="no"
LAYER2="hdlc"
LAYER3="trans"
ENCAP="syncppp"
USERCONTROL="yes"
DYNAMICIP="yes"
ASKPASSWORD="no"

*** cat /etc/sysconfig/network/ifcfg-lo
IPADDR=127.0.0.1
NETMASK=255.0.0.0
NETWORK=127.0.0.0
BROADCAST=127.255.255.255
STARTMODE=onboot
USERCONTROL=no

*** cat /etc/sysconfig/network/ifcfg-wlan-bus-usb-2-5:1.0
BOOTPROTO='static'
BROADCAST=''
ETHTOOL_OPTIONS=''
IPADDR='192.168.178.20'
MTU=''
NAME='AVM WLAN USB Device'
NETMASK='255.255.255.0'
NETWORK=''
REMOTE_IPADDR=''
STARTMODE='auto'
UNIQUE='+rmv.fKfIdV6W1uB'
USERCONTROL='yes'
WIRELESS_AP=''
WIRELESS_AUTH_MODE='sharedkey'
WIRELESS_BITRATE='auto'
WIRELESS_CA_CERT=''
WIRELESS_CHANNEL=''
WIRELESS_CLIENT_CERT=''
WIRELESS_CLIENT_KEY=''
WIRELESS_CLIENT_KEY_PASSWORD=''
WIRELESS_DEFAULT_KEY='0'
WIRELESS_EAP_AUTH=''
WIRELESS_EAP_MODE=''
WIRELESS_ESSID='FRITZ!Box Fon WLAN 7050'
WIRELESS_FREQUENCY=''
WIRELESS_KEY=''
WIRELESS_KEY_0='******'
WIRELESS_KEY_1=''
WIRELESS_KEY_2=''
WIRELESS_KEY_3=''
WIRELESS_KEY_LENGTH='128'
WIRELESS_MODE='Managed'
WIRELESS_NICK=''
WIRELESS_NWID=''
WIRELESS_PEAP_VERSION=''
WIRELESS_POWER='yes'
WIRELESS_WPA_ANONID=''
WIRELESS_WPA_IDENTITY=''
WIRELESS_WPA_PASSWORD=''
WIRELESS_WPA_PSK=''
_nm_name='bus-usb-2-5:1.0'
collectNWData.sh: Local network informations also saved in file collectNWData.out

Den Treiber von AVM kann ich auch nicht installieren. Der MAKE-Befehl endet mit folgender Ausgabe:

make -C /lib/modules/2.6.18.2-34-xenpae/build SUBDIRS=/home/hansi75/Downloads/fritz/src modules
make[1]: Entering directory `/usr/src/linux-2.6.18.2-34-obj/i386/xenpae'
make -C ../../../linux-2.6.18.2-34 O=../linux-2.6.18.2-34-obj/i386/xenpae modules
CC [M] /home/hansi75/Downloads/fritz/src/main.o
In file included from /home/hansi75/Downloads/fritz/src/main.c:31:
/home/hansi75/Downloads/fritz/src/tools.h:75: error: expected identifier or ‘(’ before ‘typeof’
/home/hansi75/Downloads/fritz/src/tools.h:75: error: expected ‘)’ before ‘__xchg’
/home/hansi75/Downloads/fritz/src/main.c:65: error: unknown field ‘owner’ specified in initializer
/home/hansi75/Downloads/fritz/src/main.c:65: warning: initialization from incompatible pointer type
make[4]: *** [/home/hansi75/Downloads/fritz/src/main.o] Fehler 1
make[3]: *** [_module_/home/hansi75/Downloads/fritz/src] Fehler 2
make[2]: *** [modules] Fehler 2
make[1]: *** [modules] Fehler 2
make[1]: Leaving directory `/usr/src/linux-2.6.18.2-34-obj/i386/xenpae'
make: *** [fwlanusb.o] Fehler 2
für hilfe wäre ich sehr dankbar
 

Jacko

Moderator
AW: Probleme mit WLAN-Stick von AVM und Suse 10.2

Klar, der Treiber von AVM geht nur für SuSE <= 10.0

Da hilft Dir also nur Ndiswrapper.

Grüße

Jacko

Nachtrag:

eth0 no wireless extensions.

sit0 no wireless extensions.

ippp0 no wireless extensions.
=> Nichts erkannt, kein WLan *g*
 

Jacko

Moderator
AW: Probleme mit WLAN-Stick von AVM und Suse 10.2

@ shubak:

Hier steht es im Moment wohl noch so wie für die 10.1. Für den WLan Stick von AVM gibts zwar nen Beta Treiber, aber der funzt nur bis zur 10.0.
Daher wirds auf der verlinkten Seite kein rpm geben können.

@ hansi:

Bemühe die Forensuche nach ndiswrapper, das hatten wir schon tausend mal und damit funzt der Stick ganz gut. Sogar mit WPA (der Beta Treiber bietet nur WEP)


Grüße

Jacko
 

hansi

New Member
AW: Probleme mit WLAN-Stick von AVM und Suse 10.2

so. ich hab das ding am laufen.

war ein bisschen langwierig, aber nur das ergebnis zählt...:)

hab mir den treiber für windows bei avm runtergeladen,
den hab hab ich entpackt,
die fwlan.inf mit ndiswrapper installiert.

das wars eigentlich auch schon.

danke trotzdem
 
Status
Für weitere Antworten geschlossen.
Oben